что такое dtcs pol
Что такое dtcs pol
Многие пользуются программкой для прошивки раций, но не знают основных параметров. Сам долго мучился, пока не нашел что зачем. Особенно касается настройки субтонов на прием/передачу.
Описания колонок и их значений в редакторе каналов памяти CHIRP.
DTCS Rx Code
Здесь DTCS код который используется для настройки шумоподавителя на приём этого кода (если рация поддерживает эту возможность) и Tone Mode (Вид Субтона) настроен на Cross (Кроссрежим)
Настройка Duplex (дуплекс) режима для канала. Если выбрано None, то частота передачи и приёма будут одинаковые.
Если +* или *- (плюс или минус), тогда частота передачи, будет выше или ниже (соответсвенно) от частоты приёма, на значение которое указано в колонке Offset (Смещение).
Если Duplex (дуплекс) настроен на split то в колонке Offset (Смещение) должна быть записана абсолютная частота передачи которая будет использоваться (если рация поддерживает эту возможность).
Здесь указывается разница между частотой передачи и приёма, для каналов которыеиспользуются в режиме Duplex (Дуплекс).
Здесь указывается модуляция приёма и передачи канала.
Используется для настройки шага переключения частот на канале.
Пропуск канала в режиме сканирования
Tone: имеются ввиду CTCSS тоны. Тон передачи указывается в колонке Tone (ТонПРД), тон приёма в ToneSql (ТонШПД).
(пустота): значит что для передачи или приёма не применяется ни один метод.
Что такое dtcs pol
цитата: Originally posted by AlekseiP:
Дак он точно такой же, как и ваш.
цитата: Originally posted by Strug71:
попробую заказать родной шнур с сайта HiTalk
цитата: Originally posted by AlekseiP:
Уточните у китайца, который вам эту станцию продал, какой шнурок для неё нужен. Может этот KPG-22 не подходит к ней.
цитата: Originally posted by AlekseiP:
Иногда даже станцию для этого разбирают
цитата: Originally posted by AlekseiP:
прогу, что китаец прислал, так и не удалось запустить?
цитата: Originally posted by Strug71:
Значит это типовой разьём для Кенвуда
цитата: Originally posted by Strug71:
..при синхронизации загорается лампа на рации а затем тухнет и входит ошибка соединения
Скорее всего кабель не тот выбрал если верить драйверу от китайца, хотя в описании BF-A5 тоже нет но вскрыл хорошо http://ru.aliexpress.com/item/. ommendVersion=1
. при синхронизации загорается лампа на рации а затем тухнет и входит ошибка соединения.
цитата: Originally posted by AlekseiP:
попробуйте выставить ПМР с его шагом, 6.25 кГц
цитата: Originally posted by AlekseiP:
Что за модель Бао?
цитата: Originally posted by Strug71:
На баофенге нет дисплея и настроек по шагу частот в CHIRP не вижу.
цитата: Originally posted by Strug71:
пробовал по быстрому. пока не выходит.
цитата: Originally posted by AlekseiP:
прогами, на которые я выше ссылки давал?
цитата: Originally posted by AlekseiP:
Или мне на почту скиньте. Почта у вас в ЛС.
цитата: Originally posted by AlekseiP:
Этот что-ли?
цитата: Originally posted by AlekseiP:
Попробуйте его переименовать.
цитата: Originally posted by Strug71:
Но прога не открывается и пишет ошибку
цитата: Originally posted by Strug71:
Приобрёл я у Китая некое изделие,ноу-нейм
цитата: Originally posted by Strug71:
Пробовал методом тыка искать подходящий софт не выходит.
цитата: Originally posted by Strug71:
ну думаю ясно. это KENWOOD TK-3207S в другой обёртке.
цитата: Originally posted by Strug71:
Но прога не открывается и пишет ошибку.
цитата: Originally posted by AlekseiP:
Эти частоты, что в табличке, используют очень серьёзные службы.
цитата: Originally posted by Fenixoid:
скажите в какой программе у вас эти пункты?
цитата: Originally posted by Strug71:
Коды пока что такое не ведаю.
цитата: Originally posted by AlekseiP:
сканирования кодов и тонов
цитата: Originally posted by AlekseiP:
Таких в природе не существует
цитата: Originally posted by Strug71:
прошивать на общепринятые
цитата: Originally posted by Mexic0:
Будете в Москве, подъезжайте
——————
С уважением, Ярослав. avtokanal.com
цитата: Originally posted by soulseeker:
«Кетай» скорее всего сидит за тональным шумодавом, а субтон вы не даёте.
цитата: Originally posted by AlekseiP:
хотите добиться?
цитата: Originally posted by Strug71:
кетай не слышит. жаль.
цитата: Originally posted by Strug71:
. это хорошо но кетай не слышит. жаль.
цитата: Originally posted by Strug71:
С Днём Рождения. Исполнения всех желаний и крепкого здоровья.
С Днём Рождения. Исполнения всех желаний и крепкого здоровья.
цитата: Originally posted by Strug71:
интересно В3 версия в каких пределах должна передавать
цитата: Originally posted by Strug71:
еська не передаёт
цитата: Originally posted by Fenixoid:
частотомер встроенный!
CHIRP
Tone Modes in CHIRP¶
An empty Memory.tmode means that no tone is transmitted or received
A Memory.tmode of «Tone» means that the radio will transmit a single sub-audible tone, according to the Memory.rtone value. In this mode, the receiver is carrier squelch.
A Memory.tmode of «TSQL» means that the radio will transmit a sub-audible tone, according to either the Memory.rtone or Memory.ctone value. In this mode, the receiver uses tone squelch with the same value as the transmitter. If the radio’s feature set includes «has_ctone» (most Icom and Kenwood radios) then the value used in this case is Memory.ctone. Otherwise, use Memory.rtone.
A Memory.tmode of «DTCS» means that the radio will transmit a DCS code, according to either the Memory.dtcs or Memory.rx_dtcs value. In this mode, the receiver uses DTCS squelch with the same value of the transmitter. If the radio’s feature set includes «has_rx_dtcs» then the value used in this case is Memory.rx_dtcs. Otherwise, use Memory.dtcs.
TSQL-R¶
A Memory.tmode of «TSQL-R» means that the radio will squelch when the tone is received and use carrier squelch if not. This is usually used to listen for transmissions that should not be there. If the radio’s feature set includes «has_ctone» then the value used in this case is Memory.ctone. Otherwise, use Memory.rtone.
DTCS-R¶
A Memory.mode of «DTCS-R» means that the radio will not transmit a sub-audible tone, but will squelch the receiver when the specified DCS is present and use carrier squelch when it is not. If the radio’s feature set includes «has_rx_dtcs» then the value used in this case is Memory.rx_dtcs. Otherwise, use Memory.dtcs.
Cross¶
A Memory.tmode of «Cross» means that the radio will use an asymmetric squelch configuration according to the value of Memory.cross_mode:
Tone->Tone¶
A cross_mode of «Tone->Tone» means the radio will transmit one sub-audible and will use another tone to open the receive squelch. The tone values are in Memory.rtone and Memory.ctone respectively. By convention, the driver code generally expects «Cross»: «Tone->Tone» to be used only when the two tones are different, and a mode of «TSQL» to be used when the tones are the same.
Tone->DTCS¶
A cross mode of «Tone->DTCS» means that the radio will use a sub-audible tone for transmit, according to Memory.rtone, and a DCS code for receiver squelch. If the radio’s feature set includes «has_rx_dtcs» then the value used in this case is Memory.rx_dtcs. Otherwise, use Memory.dtcs
DTCS->Tone¶
A cross mode of «DTCS->Tone» means that the radio will use a DCS code for transmit, according to Memory.dtcs, and a sub-audible tone for receiver squelch. If the radio’s feature set includes «has_ctone» then the value used in this case is Memory.ctone. Otherwise, use Memory.rtone.
A cross mode of «->Tone» means that the radio will not transmit a sub-audible tone, but will enable tone squelch on the receiver. If the radio’s feature set includes «has_ctone» then the value used in this case is Memory.ctone. Otherwise, use Memory.rtone.
A cross mode of «->DTCS» means that the radio will not transmit a sub-audible tone, but will enable DCS squelch on the receiver. If the radio’s feature set includes «has_rx_dtcs» then the value used in this case is Memory.rx_dtcs. Otherwise, use Memory.dtcs.
A cross mode of «DTCS->» means that the radio will use a DCS code for transmit, according to Memory.dtcs. In this mode, the receiver is carrier squelch.
DTCS->DTCS¶
A cross mode of «DTCS->DTCS» means that the radio will transmit a DCS code and will use a DSC code to open the squelch. The code values are Memory.dtcs and Memory.rx_dtcs respectively. By convention, CHIRP generally uses «Cross»:»DTCS->DTCS» when the two codes are different, and uses a mode of «DTCS» when they are the same.
Radio Behavior¶
Icom/Kenwood style¶
Most (maybe all?) Icoms and Kenwoods behave in a specific way. They store two tone values, one of which gets used in Tone mode, and the other which gets used in TSQL (CTCSS) mode. No Icom (that I’m aware of) can use the two values for separate TX and RX tones, nor can most Kenwoods. However, at least the Kenwood D72 can operate this way.
Yaesu style¶
Older Yaesu radios store just a single tone value, which gets used regardless of whether or not the radio is in Tone or TSQL mode.
Newer Yaesu HTs use both rtone and ctone. These radios support all of the ctcss modes. They also store separate DTCS transmit and receive. they support all modes except DTCS-R and all cross modes except TONE->DTCS and DTCS->Tone.
Commercial style (Wouxun, Baofeng, etc)¶
These radios store separate TX and RX tones all the time (and often overload the same field for DTCS and tone values, storing a flag if the value is not to be used). These are effectively in «Cross» mode all the time, but CHIRP detects the common modes and provides the appearance of the other radios (emulating Tone, TSQL, and DTCS where possible).
Memory tone fields usage matrix¶
This table summarize which memory fields are used in each tone mode.
CHIRP
Understanding CHIRP’s columns¶
This document is intended to help users understand the meaning of each column in the channel editor. In most cases, the default value for a column can be used if you don’t know what the meaning of the column is.
Users unfamiliar with programming radios are encouraged to enable Hide Unused Fields mode in the View menu. Also, enabling Smart Tone Modes in the same location can be rather helpful for reducing confusion.
This is the location or «channel number» of the memory. The limits of what can be in this field are defined by your radio.
Frequency¶
This defines the receive frequency of the channel in Megahertz. If Duplex is set to None, then it is also the transmit frequency of the channel.
This is the alphanumeric label for the memory, as displayed on the front panel. The length and valid characters are defined by what the radio is capable of supporting.
Tone Mode¶
This sets the mode used to transmit or receive squelch tones (or related selective calling technologies). The following explains what the options means:
This sets the CTCSS tone to be transmitted if the Tone Mode is set to Tone. In Cross mode, it has additional meanings (see description of Cross Mode for more details).
ToneSql¶
This sets the CTCSS tone to be transmitted and used for receiver squelch if the Tone Mode is set to TSQL. In Cross mode it has additional meanings (see description of Cross Mode for more details).
DTCS Code¶
This sets the DTCS code to be transmitted and used for receiver squelch if the Tone Mode is set to DTCS. In Cross mode it has additional meanings (see description of Cross Mode for more details).
DTCS Rx Code¶
This sets the DTCS code to be used for receiver squelch (if the radio supports this capability) and Tone Mode is set to Cross (see description of Cross Mode for more details).
DTCS Pol¶
This sets the DTCS polarity of the transmitted code and the code used for the receive squelch any time DTCS is used for transmit or receive squelch. The first character pertains to the transmit polarity and the second pertains to receive polarity. The corresponding character is N for normal or R for reversed (aka «inverted») polarity.
Duplex¶
This sets the duplex mode of the channel. If set to (None) then the transmit and receive frequencies are the same. If set to either +* or *- (plus or minus) then the transmit frequency will be either above or below (respectively) the receive frequency by the value of the Offset field.
If the duplex is set to split then the Offset field should contain the absolute transmit frequency to be used (if the radio supports this capability).
If the duplex is set to off then transmission on this channel will be disabled (if the radio supports this capability).
Note that for simplex channels, this should be set to (None) and repeater channels should have this set to either +,-, or split.
Offset¶
This sets the amount of difference between the transmit and receive frequencies used for the channel if Duplex is not (None) or off (in which case it is ignored). If the Duplex is set to a shift direction, then the Offset field should be set to the amount (in Megahertz) above or below the receive frequency to shift to find the transmit frequency. If Duplex is set to split then the Offset field should be set to an absolute transmit frequency.
This controls the transmit and receive mode of the channel. The following lists the common values and their meanings:
Tune Step¶
The tuning step used to channelize the receive frequency.
The scan skip mode for the channel. The values and their meanings are:
Cross Mode¶
This field controls the squelch behavior of the channel when the Tone Mode is set to Cross. Each value consists of two technologies separated by an arrow (->). The value to the left of the arrow controls the selective-call method used on transmit, while the one to the right of the arrow controls the receive squelch. The possible values are:
The Cross Mode field allows addressing more commercial modes of squelch operation, such as using different tones or codes for transmit and receive. For example:
Что такое dtcs pol
CHIRP. Колонки в редакторе каналов
Описания колонок и их значений в редакторе каналов памяти CHIRP.
В этом поле указывается частота приёма канала в Мегагерцах.. Если дуплекс выключен, то это будет также и частотой передачи.
Имя канала, которое вы можете написать в на латинице или цифрами. Максимальное и минимальное количество знаков этого поля разные для каждых радиостанций, поэтому нужно смотреть эти значения в характеристиках вашей рации.
В этом поле настраивается режим приёма или передачи тонов. Ниже значения поля, и их назначение:
DTCS Rx Code
Здесь DTCS код который используется для настройки шумоподавителя на приём этого кода (если рация поддерживает эту возможность) и Tone Mode (Вид Субтона) настроен на Cross (Кроссрежим)
DTCS Pol
Настройка Duplex (дуплекс) режима для канала. Если выбрано None, то частота передачи и приёма будут одинаковые.
Если +* или *— (плюс или минус), тогда частота передачи, будет выше или ниже (соответсвенно) от частоты приёма, на значение которое указано в колонке Offset (Смещение).
Если Duplex (дуплекс) настроен на split то в колонке Offset (Смещение) должна быть записана абсолютная частота передачи которая будет использоваться (если рация поддерживает эту возможность).
Здесь указывается разница между частотой передачи и приёма, для каналов которые используются в режиме Duplex (Дуплекс).
Здесь указывается модуляция приёма и передачи канала.
Используется для настройки шага переключения частот на канале.
Пропуск канала в режиме сканирования
Tone: имеются ввиду CTCSS тоны. Тон передачи указывается в колонке Tone (ТонПРД), тон приёма в ToneSql (ТонШПД).
(пустота): значит что для передачи или приёма не применяется ни один метод.
Возможные значения поля :